Excludes shipments to Alaska, Hawaii, U. There is also an easy way to reset the oil and inspection dashboard lamps. The housing is oriented differently for Cooper See and Cooper S See models. Should this sensor be replaced? It's a tight fit to get the socket on there. February 19, 2014 Followup from the Pelican Staff: Are you saying the new dipstick reads over-full? This article applies to the. It is possible the oil viscosity is breaking down, or? The stick shows oil over the marks.
Use the 27mm socket to remove the top of the housing slowly; You will then see the old filter cartridge in the housing. I bought the new filter kit from the local Mini dealer but it will not fit over the black plastic core that is attached to the oil filter housing. I know its only 0. Some product and company names mentioned on this site may be trademarks of their respective owners. May 29, 2016 Followup from the Pelican Staff: I only see the felt top of the filter, no seal in fig 7.
Now carefully remove the filter housing cover. Add about 4 quarts to the engine, and check the dipstick. Join us in our and ask a question to one of our many automotive experts. You can use a special tool to perform this reset, and the Peake Research R5 tool discussed in Project 28 also does the trick. See Remove the top slowly to allow the oil to drain back into the housing, and underneath you will see the cartridge filter. The plug itself is cheap, so it's added insurance against oil leaks.
Add about 4 quarts to the engine, and check the dipstick. Will all the used oil drain when the front of the vehicle is on ramps? May 11, 2014 Followup from the Pelican Staff: Are you working from above? Continue to add about a half a quart at a time and keep checking the dipstick. Is it possible to change the oil filter and after the work is done the housing still has the dry dust and dirt on it that it went in with? This should be facing down when you install the filter. The oil will be very hot, and will empty out extremely quickly, so be careful not to burn yourself wear rubber gloves. If the oil level is not at the top point, then top it off until it reaches the top point of the dipstick.
Don't forget to use the new crush washer on the oil pan drain plug. I love the whine of the supercharger. Other than looking at a part number on the housing, it is hard to tell. It's on there, not over tightened so what could be the problem? Traditionally, the characteristics of motor oil were linked closely to its weight. Pull the old element out and place the new element in its place. Give our parts specialists a call at 1-888-280-7799.
See and There will be no time to grab any more buckets or oil pans if you underestimate, so make sure that the one you choose is big enough. September 3, 2018 Followup from the Pelican Staff: The seal should sit flush over the small shoulder on the drain plug. New filter in the housing. February 26, 2015 Followup from the Pelican Staff: Yes, we sell the filter. They can help you find the right oil. Do they leave debris or oil in the pan or it's not more than a traditional drain from the pan? March 26, 2013 Followup from the Pelican Staff: I would replace when you change your engine oil.
In general, if you live in a cold climate, you should use a 10W-40 or similar oil. See green arrow in There is a 36mm nut on the cap that is located on top of the housing. Fill it up until it reaches the top mark of the dipstick - the engine oil level will automatically lower when the oil filter fills up with oil. Nick replied to anothe question with the picture he says just put it back. On the last install of the new oil filter I found a spare part that I did not recognize laying on the ground just as I was cleaning up.
Her car has the 36mm nut on the housing. Figure 10 Fill your engine with the new oil from the oil filler hole in the top of the valve cover. Join us in our and ask a question to one of our many automotive experts. However, if synthetic oil was the only type of oil that your engine has seen, I usually recommend sticking with it. After installing it the oil light stays on. This is one of the rare occasions where you find a standard fitting on a metric car. There is a 27mm nut on the top of the filter housing.
So what's your take on this? Once you see these lights come up, release the trip reset button. The first thing you need to do is to make sure that you have everything that is required for the job. Same day shipping does not apply if your order is placed over the weekend or on a major U. At this point, I like to top the oil off at the top point on the dipstick. Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your engine. Have plenty of paper towels on hand, as oil will spill from the filter if you're not careful.
January 5, 2016 Followup from the Pelican Staff: I would assume you have either a pressure drop, sensor failure or wiring issue. Now press and hold both buttons on the tachometer. Start by driving the car around, and let it heat up to operating temperature. Fill it up until it reaches the top mark of the dipstick - the engine oil level will automatically lower when the oil filter fills up with oil. August 8, 2014 Followup from the Pelican Staff: No problem. The engine oil works as a lubricant. Then lubricate the O-ring with clean engine oil.