We need to have the assembly number at time of the order it can ensure that you obtain a direct drop in replacement. You will use existing yokes and switches from you old unit whenever changing the particular transfer case. Call Surefire at 1-800-790-9094 for customer service, availability and technical assistance. Encoder motors are available separately. I have a 1998 F250 with 207,000 miles and the 4 wheel drive quit working.
I just cut the old ground wire and left it hang and installed this motor. The vacuum soleniod and vacuum lines need to be replaced. I used some black gasket maker I had laying around, probably isn't required. All possible upgrades are included into the units during the building process, all units are pressure and spin tested by experienced automotive specialists. I would definitely recommend this shift motor. Rear output type: slip yoke. My boyfriend did not believe it and then an hour later he was driving and I did it again.
Having problems with your electric shift, we off a complete line of remanufactured encorder motors, just look up your application and you will be able to referecne the replacement encorder motor. Correct Ford F150 Transfer Case the first time! Went on in 15 min taking my time. Step 6 - Replace the wiring harness Replace the wiring harness. Not offered by most builders. It is located behind the transfer case, which is mounted behind the transmission. We were stuck for a long period of time.
Since suit and tie people are afraid of gettting a little dirty, we people who get dirty and work on our cars and trucks have a harder time, not because we are the dumb ones, because suit and ties are the dumb ones. I thought I would have to get a different motor, but I'm stupid so I just drilled the hole out and plugged the wire into the now open port. Anyhow, the quality of the part seems good. Be sure to note the colors and locations of these other wires. Re manufactured units have more new parts and come with a 12 month warranty. The manufacturer was not contacted.
This helps with traction, and is commonly used in wet, snowy, off-road, or elevated areas. The vehicle was inspected by a dealer who informed the contact that he would need to replace the actuator for the gear shift. It is a critical component that can be easily worn out over time. On the contrary, the Ford F150 transfer case motor is an integral part of your four-wheel-drive, and if it malfunctions, you will have to contend with 2005 Ford F150 transfer case problems. This article will cover how to replace it yourself to save you. All other parts that do not have absolutely new potential service life are replaced with the highest quality parts available.
Step 7 - Reconnect the battery terminals Reconnect the battery terminals, lower the truck, and check your 4x4 function. A transfer case motor can wear out, be damaged by debris, or corrode over time. I installed the part in 15 minutes, correctly. Relay box 2 Ford F150 1999-2003. The vehicle was not taken to the dealer for the failure. Routine maintenance can prevent damage to the transfer case motor. As a result, the rear end of the vehicle fishtailed.
Original proof of purchase is required. Catalytic converters cannot fail on there own and the original cause of failure must be repaired to prevent repeated converter failure. It goes on easily and the only thing you need to know for installation is that this one does not use the seperate ground wire as the old one did. Warranty covers material and workmanship including parts and labor at the factory. Low service expectancy parts are automatically replaced regardless of their condition. The main harness is connected via a clip. While driving 50 mph in snowy conditions, the electronic 4-wheel drive disengaged and shifted into 2-wheel drive without warning.
Locating the motor might be the most difficult part of this task. In fact, you may not even know that the transfer case motor exists. Proven Force a major industry vehicle re-builder of Four wheel drive transfer cases, as well as service provider for light and medium vehicles with over 38 years experience. Another thing to consider is that it takes less mechanical skills to remove and replace a complete unit than it does to rebuild a unit if you are considering doing the job yourself also less time. Commercial, heavy duty, custom, or off road vehicle use voids the warranty.
The yellow and orange were to thick even on the oem plug to remove. After tracing wires color for color, it was easier to spice the 2 thicker ones and move the 5 thinner ones to old plug. Use a flat head screw driver to pry the motor off; if there is any corrosion, then the transfer case motor can really stick to the transfer case. We stock transfer case motor parts for most Ford models including , , , , , , , , , , , and. The contact then engaged the accelerated and noticed that the vehicle was in four wheel drive but the four wheel drive would not activate. This article applies to the Ford F-150.
Make sure not to over-tighten the bolts or pinch any of the wires that need to be placed back into the wiring harness. Without speedo hole, 31 spline input, 31 rear slip, cupped front output yoke. Let me just start out to say that PartsGeek is great. Purchase one of these encoder motors at the same time as transfer case and take a 10% discount on the encoder motor! The person offering the rebuild service gives you a price typically without opening up your transfer case. Step 5 - Install the new shift motor Install the new replacement motor onto the transfer case.